Free Grout Calculator for Any Tile Size and Joint Width

Construction Pedia · Calculators

A grout calculator multiplies the joint volume inside each square foot of tile by the grout’s density, then scales that figure to your floor or wall. A 120-square-foot (11.1 m²) floor of 12×24-inch tile with 1/8-inch (3 mm) joints needs about 6.8 pounds (3.1 kg) of grout, including 10% waste. Enter your own sizes below.

Grout Calculator: Enter Your Tile and Joint Sizes

Common tile sizes

Enter actual tile size, not the box label. Thickness equals joint depth. Use 10% waste for glazed tile, 20 to 25% for quarry tile and porous stone. 106 lb/ft³ (1.70 kg/L) fits standard cement grout; check epoxy and urethane bags for their own yield.

Example: 120 sq ft bathroom floor
6.8lb
3.1 kg of grout, waste included
125 lb (11.3 kg) bags
110 lb (4.5 kg) bags
0.052lb per sq ft
5.2lb per 100 sq ft
Sanded grout

Layout to scale (joint width shown true size relative to tile)

Key Takeaways

  • Measure actual tile thickness, because it sets joint depth and changes the result as much as joint width does.
  • Expect 2×2-inch mosaic to use 27.6 lb per 100 sq ft at a 1/8-inch joint, about 5 times what 12×24-inch tile uses.
  • Add 10% for waste, plus another 10 to 15% for unglazed quarry tile.
  • Choose unsanded grout if joints are narrower than 1/8 inch (3 mm), and sanded grout at 1/8 inch and wider.
  • Size joints at 3 times the tile’s facial variation, never under 1/16 inch (1.6 mm).
  • Round every grout estimate up to whole 10 lb (4.5 kg) or 25 lb (11.3 kg) bags.

Inputs the Calculator Needs

  1. Tile length and width, in inches (mm)
  2. Tile thickness, which sets joint depth
  3. Joint width, from 1/16 to 1/2 inch (1.6 to 12.7 mm)
  4. Area, in square feet (sq ft) or square meters (m²)
  5. Waste factor, 10% by default

Measure a real tile with a tape or calipers. Box labels list nominal size, and a “12×24” porcelain plank made to metric dimensions measures 11.81 x 23.62 inches (300 x 600 mm). For area, treat this page as a square foot calculator for tile: split the room into rectangles, multiply length by width in feet for each one, then add them up.

How Much Grout Do I Need?

You need about 5.2 lb (2.4 kg) of grout per 100 sq ft (9.3 m²) for 12×24-inch tile with 1/8-inch joints, and 27.6 lb (12.5 kg) for 2×2-inch mosaic at the same width. Tile size and joint width drive that gap. Two floors of identical area can differ by more than 5 times in grout demand.

The Grout Coverage Formula

Manufacturers such as MAPEI and Weber use one volumetric formula:

Pounds per sq ft = [(L + W) ÷ (L × W)] × J × D × 106 ÷ 12
  • L and W: tile length and width, in inches
  • J: joint width, in inches
  • D: joint depth (tile thickness), in inches
  • 106: cement grout density in lb per cubic foot (1.70 kg/L)

The first bracket captures joint length, and smaller tiles carry more of it. The ÷ 12 term converts cubic inches per square foot into cubic feet. Epoxy and urethane grouts weigh less per unit of volume, so check the coverage table on their packaging.

Worked Example: 120 Sq Ft of 12×24 Tile

  1. (12 + 24) ÷ (12 × 24) = 0.125
  2. 0.125 × 0.125-inch joint × 0.375-inch depth = 0.00586
  3. 0.00586 × 106 ÷ 12 = 0.0518 lb per sq ft
  4. 0.0518 × 120 sq ft = 6.2 lb (2.8 kg)
  5. 6.2 lb × 1.10 waste = 6.8 lb (3.1 kg), or one 10 lb bag

That’s the gap between a generic how much grout do I need calculator and one that asks for depth. Leave thickness out, and the result can miss by a third or more.

How Much Grout Per Square Foot Does Each Tile Size Use?

Grout use runs from 0.017 lb per sq ft (0.08 kg/m²) for 24×24-inch tile with 1/16-inch joints up to 0.55 lb per sq ft (2.7 kg/m²) for 2×2-inch mosaic with 1/4-inch joints. The chart below lists pounds per 100 sq ft at a cement grout density of 106 lb per cubic foot (1.70 kg/L).

Tile size (thickness)1/16 in (1.6 mm)1/8 in (3 mm)3/16 in (5 mm)1/4 in (6 mm)
2×2 mosaic (1/4 in)13.8 lb (6.3 kg)27.6 lb (12.5 kg)41.5 lb (18.8 kg)55.3 lb (25.1 kg)
3×6 subway (5/16 in)8.6 lb (3.9 kg)17.3 lb (7.8 kg)25.9 lb (11.7 kg)34.5 lb (15.6 kg)
12×12 (3/8 in)3.5 lb (1.6 kg)6.9 lb (3.1 kg)10.4 lb (4.7 kg)13.8 lb (6.3 kg)
6×36 plank (3/8 in)4.0 lb (1.8 kg)8.1 lb (3.7 kg)12.1 lb (5.5 kg)16.1 lb (7.3 kg)
12×24 (3/8 in)2.6 lb (1.2 kg)5.2 lb (2.4 kg)7.8 lb (3.5 kg)10.4 lb (4.7 kg)
24×24 (3/8 in)1.7 lb (0.8 kg)3.5 lb (1.6 kg)5.2 lb (2.4 kg)6.9 lb (3.1 kg)

Mosaic sheets explain the top row. A 2×2 layout packs 12 linear feet of joint into each square foot, while 12×24 tile holds just 1.5 feet. Values exclude waste.

Which Joint Width Should You Use?

Use a joint at least 3 times the tile’s actual size variation, and never narrower than 1/16 inch (1.6 mm), per American National Standards Institute (ANSI) A108.02 Section 4.3.8. Tile that varies 1/16 inch across a box needs a 3/16-inch (4.8 mm) joint. That rule protects straight grout lines.

Offset layouts tighten the limits. With any tile side over 15 inches (381 mm) in running bond, ANSI calls for at least 1/8 inch on rectified tile and 3/16 inch on calibrated tile, and the Tile Council of North America (TCNA) Handbook repeats the same numbers. Width hits your budget directly: moving from 1/8 to 3/16 inch raises grout use by 50%.

Which Grout Type Fits Your Joint Width?

Use unsanded grout for joints narrower than 1/8 inch (3 mm) and sanded grout for joints 1/8 inch and wider. Epoxy works at either width and resists stains and harsh cleaners, which is why commercial kitchens and steam showers specify it.

Grout typeJoint widthBest useANSI standard
Unsanded cementUnder 1/8 in (3 mm)Wall tile, glass tile, polished marbleA118.6 / A118.7
Sanded cement1/8 to 1/2 in (3 to 12.7 mm)Floors, porcelain, quarry tileA118.6 / A118.7
Epoxy1/16 to 1/2 in (1.6 to 12.7 mm)Kitchens, showers, high-stain areasA118.3
Urethane (premixed)1/16 to 3/8 in (1.6 to 9.5 mm)DIY floors and backsplashesPer maker

Sand scratches soft surfaces. Glass tile and polished stone take unsanded or epoxy grout, even at 1/8 inch.

How Much Extra Grout Should You Buy for Waste?

Add 10% to the calculated amount for spillage and cleanup, then round up to the next full bag. LATICRETE adds another 10 to 15% for unglazed quarry tile, since porous faces soak up grout. MAPEI’s US calculator recommends a 5 to 10% overage.

Those two figures don’t conflict. MAPEI’s tool runs on product-specific density and actual volume, while LATICRETE bases coverage on nominal tile size, so it builds in a wider buffer. Stick with 10% for glazed ceramic and porcelain. Go to 20 or 25% for quarry tile, saltillo, and tumbled stone.

How Do MAPEI, LATICRETE, and TEC Grout Calculators Compare?

The MAPEI grout calculator and the LATICRETE grout calculator give product-specific results, while the TEC grout calculator link currently redirects to an unrelated product page. MAPEI multiplies joint volume by density, and LATICRETE’s Project Estimator handles grout alongside mortar and membranes.

ToolJoint depth inputOutputWaste advice
MAPEI (US)Tile thicknessQuantity and estimated cost5 to 10%
LATICRETETile size and thicknessProduct units10%, plus 10 to 15% for quarry tile
MerkreteSeparate depth fieldPounds, 25 lb bags, 1 and 2 gal unitsNone stated
TECNot availableRedirectsNot available

Searches for “grout calculator MAPEI” return 2 regional versions. The Australian page works in metric and lists only MAPEI products, so US buyers belong on the US page. A brand-neutral grout coverage calculator suits anyone still comparing products, since it shows pounds before you commit to a bag size.

FAQs

Can I use unsanded grout on a floor?

No, not for joints 1/8 inch (3 mm) or wider, where unsanded grout shrinks and cracks under foot traffic. Narrow floor joints under 1/8 inch handle it fine.

How many square feet does a 25 lb bag of grout cover?

A 25 lb (11.3 kg) bag covers about 480 sq ft (44.6 m²) of 12×24-inch tile with 1/8-inch joints. That same bag stretches only 90 sq ft (8.4 m²) on 2×2 mosaic.

Does tile thickness change how much grout I need?

Yes. A 1/2-inch tile uses 33% more grout than a 3/8-inch tile of identical size and joint width, because joint depth matches tile thickness.

Should I buy all my grout at once?

Yes. Buy every bag from one production lot to keep color consistent. LATICRETE advises blending bags with different control numbers, following Materials and Methods Standards Association (MMSA) Bulletin #9.

How do I calculate grout for hexagon or penny round tile?

Enter a hexagon’s width across the flats as both length and width, which yields identical joint length per square foot. Penny round leaves larger gaps, so rely on the manufacturer’s mosaic coverage chart.

Plan Your Next Tile Job With Real Numbers

Grout is cheap. Running short halfway through a floor isn’t, since a second lot can dry a shade off. Measure your tile, confirm the joint width against ANSI A108.02, and let the calculator turn those numbers into a bag count before you drive to the supply house. Newer urethane and single-component grouts keep shifting the density math, so check the coverage table on any new product against your result.

Sources

Rachel Park

Rachel Park leads sustainability, roofing, and building materials content at Constructionspedia, drawing on over 10 years of commercial and residential construction experience. She holds an M.S. in Sustainable Building Systems from UC Berkeley and is a LEED AP BD+C, specializing in roofing systems, insulation, waterproofing, and energy-efficient materials. Her research-backed guides help homeowners and industry professionals make informed decisions about construction and green building.

Related Posts